You may also like. Electric Welding Machine IGBT MIG TIG Inverter ARC MMA Stick Welder With Gas. AUTOOL M528 MIG ARC Digital Inverter Welder can provide a variety of welding types, including manual welding, argon arc welding, gas shielded welding. It can be used for welding carbon steel, stainless steel, aluminum alloy, and other materials and for welding solid wire and flux-cored. It is features fully digital control; stable output; compact size, lightweight, high efficiency, and energy-saving; easy arc starting, stable welding process, good formation; easy installation, and simple operation. [Multiple Welding Modes]: AUTOOL M528 MIG ARC Digital Inverter is an all-in-one welder with MMA mode, MIG mode and TIG mode, perfectly suitable for welding multiple different work pieces, such as carbon steel, stainless steel, aluminum alloy, and other materials. [2T/4T/ Spot Wire Feeding Modes]: Three different wire feeding modes are available to adjust the wire feeding frequency as required. Using a high-quality wire feeding machine(iron) to ensure smooth wire feed. [Energy Saving &Convenient]: This is optimized to deliver a flawless welding, making spatter and post-weld cleanup almost non-existent. Portable handle makes it easier to operate, the lightweight makes it more convenient to carry around. [Current&Voltage Display]: Voltage display: The gas shielded welding mode displays the preset value, and the manual welding mode displays the actual value; Current display: MIG mode shows wire feed speed preset value and actual current during welding, while MMA mode and LIFT TIG mode show current preset value. [Adjustable welding parameters]: Speed adjustment: Adjust the wire feed speed in MIG mode; Voltage adjustment: functions only in MIG mode to regulate voltage; Inductance adjustment: works in MIG mode to adjust the hardness and softness of the arc, and in MMA mode and LIFT TIG mode to adjust the current. ACCORDING THE MACHINE TYPE USE POWER SUPPLY. 1 Check the connection of work piece, earth cable, welding torch, gas cylinder, regulator and hose, make sure they are firm and reliable. 2 Switch on the power source. 3 Turn on the gas valve, adjust gas volume to 3-5L/MIN. Check if there is gas leaking. 4 Hold the torch and keep tip of Tungsten electrode 2-3 mm above the work piece, and tilt 20-30 to vertical direction. Aim Tungsten electrode to the welding seam. 5 Push torch switch, after arc is ignited, move the torch along seam evenly. Fine tune the welding parameter to obtain exquisite welding seam. Release the torch switch to finish a welding cycle. 6 After finish operation, turn off the gas valve, push torch switch to clear the residual gas in the regulator. At the end, turn off welding power source and wall switch. When using an open arc process, it is necessary to use correct eye, head, and body protection. Fault code: E01 Overheating E02 Output control section is damaged or dead E03 Did not give the driver board signal, but the actual voltage output E04 Internal fault. Install procedure: 1 Welding machine should be installed in a stable position and with good ventilation. Avoid direct sun outdoors. Avoid transport in invert or side position. 2 Connect electrode holder, earth cable, according to connection diagram. 3 Use 8 heat-resistant PVC hose connect the flow meter with the gas 4 Commission the machine after the machine is installed and tested. The second function description Receiving arc voltage: MIG state when the function is Receiving arc voltage adjust MMA state when the function is arc force adjust Spot welding status, functions as spot welding time adjust Receiving arc current: MIG state when the function is Receiving arc current adjust MMA state when the function is welding current adjust Spot welding status, functions as spot welding interval adjust Electronic Inductor: MIG state when the function is electronic Inductor adjust MMA state when the function is invalid Spot welding status, functions as electronic Inductor adjust No displayheader Fan does not rotateNo welding output 1, confirmed air switch is closed. 2, the input cable connected to an electric power source. Fans turnNo error codeNo welding output 1, the inspection machine all kinds of patch cords is bad. 2, the control circuit problem, find the cause, or contact your dealer. 3, on-off control lines torch. 4, torch cable break. 5, ground off or not connected to the workpiece. 6, the internal cable off. Error code E01No welding output 1, may be overheating protection, wait 2-3 minutes to restore the machine to work. 2, the temperature switch is broken using the welding current does not remain stable during: 1, grid voltage changes; 2, severe interference from the power grid or other electrical equipment. 3, welding current and welding voltage is too low or too high, you should adjust the suitable welding current and welding voltage. 1 AUTOOL M528 MIG ARC Digital Inverter Welder Main unit 1 User manual 1 MIG welding torchTorch accessories are included 1 set complete set of welding clamps 1 set Complete set of earth clamps 1 Face shield 1 Slag hammer. 3Before any return, a. 1We are a professional automotive tools company, with own factory located in China. 2We are a professional authorized dealers of. Also offer reasonable prices , excellent customer service and a reliable credit standing are our target. 3 We own three warehouse in the world: China warehouse, United States warehouse, Germany warehous. Our normal working hours are from. All messages will be answered within 24 hours. You are welcome to write at any time! The item “Electric Welding Machine IGBT MIG TIG Inverter ARC MMA Stick Welder With Gas” is in sale since Tuesday, June 22, 2021. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\MIG Welders”. The seller is “obd-worldwide2019″ and is located in Shenzhen. This item can be shipped worldwide.
- Country/Region of Manufacture: China
- Feed: Automatic Feed
- Item Type: MIG Welder
- Welding Process: MIG
- Warranty: 3 Year
- Features: Line Voltage Compensation
- Welded Material: Stainless Steel
- MPN: Does Not Apply
- Brand: AUTOOL
- Voltage: 110V / 220V
- Model: M528
- Welding Thickness: 2-10mm
- Size: 40x35x20cm
- Weight: 9.6Kg
